??????? 一個驅動裝置被釋放后，它將可以通過一個新的啟動命令來啟動。
??????? 9?Electrical safety devices
??????? 1.1.1.1.1?電氣安全裝置
??????? The switching arrangements of electrical safety devices, shall be of positive opening operation in accordance with Chapter 3 of EN 60947-5-1. (i.e. "safety switches" as defined in 3.6.1 above).
??????? 開關的電氣安全裝置的安排，應積極開放的操作在3章按照恩60947-5-1。（即“安全開關”的定義在3.6.1以上）。
??????? With the exception, on automatic parking equipment, of ultimate switches on movements with a vertical component and those on horizontal movements without mechanical limiting devices other types of switching arrangement may be used, subject to the following conditions:
??????? 對于自動停車設備，極限開關與垂直與水平分量的運動沒有機械限位裝置的其他類型的可用于運動的開關裝置的異常處理，必須符合下列條件：
??????? i)?mechanically actuated electrical switches which are not "safety type" switches, shall be duplicated, shall utilise break contacts and the switches shall be wired in series.?
??????? 1?機械驅動的電氣開關，如果不是采用“安全型”開關，應使用斷接點和開關應有線系列。
??????? ii)?If sensing devices are used they shall be automatically monitored, which shall at least ensure that an error signal or faulty operation of the sensing device shall be detected prior to the start of the associated movement, i.e. shall meet the requirements of at least EN 61496-1 type 2.
??????? 2?如果使用感測裝置應被自動監測，應確保至少一個錯誤的信號或誤操作能夠在啟動之前被?傳感裝置檢測到，即至少應滿足61496-12型的要求。
??????? iii)?If the monitoring system (see 5.11.14), shall detect an error signal, or unacceptable signal deviation, the monitoring system shall automatically initiate positive interruption of the associated powered movement and prevent further movement in that direction.
??????? 3?如果監測系統（見5.11.14），檢測到一個錯誤的信號，或不可接受的偏差信號，監控系統應自動啟動相關的防止繼續運動的系統，停止正在進行的運動。
??????? 10?Hydraulic safety devices
??????? 1.1.1.1.2?液壓安全裝置
??????? Hydraulic safety devices shall be designed and installed to achieve a safety level comparable to the requirements for electrical safety devices specified above.
??????? 液壓安全裝置的設計和安裝應能達到滿足電氣安全裝置上面指定的要求的安全水平。
??????? 11?Mechanical safety devices
??????? 1.1.1.1.3 機械安全裝置
??????? Mechanical safety devices shall be designed and installed to achieve a safety level comparable to the requirements for electrical safety devices specified above.
??????? 機械安全裝置的設計和安裝應能達到與電氣安全裝置上面指定的要求的安全水平。
??????? 12?Transmission elements used for safety purposes
??????? 1.1.1.2?安全性傳動元件
??????? Transmission elements, e.g. safety related wiring, pipework, rods, safety ropes, chains, shall be designed so that failure shall not lead to a dangerous condition. In the event of failure or rupture, a category "0" or category "1" stop function shall be automatically initiated, as appropriate to be compatible with the design (see EN 60204-1, clause 9.2.2).
??????? 傳動元件，如安全相關的電器，管道，桿，安全繩，鏈，應該被設計為即使故障也不會導致危險。在故障或破裂的事件，一種處于“0”或“1”的范疇，則應自動停止，應與設計相匹配（見EN 60204-1，第9.2.2）。
??????? The stop function shall comply with EN 954 -1, clause 5.2. Mechanical components shall have factors of safety of at least 4 to 1 in relation to maximum intended loading, without permanent deformation or failure.
??????? 停止功能應符合EN 954 - 1，5.2條款。機械零部件應具有與最大的預期負荷相關的至少4到1個安全的因素，無永久性變形或破壞。
??????? All flexible piping, flexible hoses and also any rigid pipework or connections used as transmission elements for safety purposes, shall be designed to withstand at least 4 x maximum working pressure without failure or permanent deformation.
??????? 所有軟管，軟管和剛性管道或任何連接安全性的傳動元件，設計應能承受至少4×最大工作壓力且無故障或永久變形。
???????
??????? The safety factor for the overspeed governor rope shall be at least 8 to 1, computed from the maximum force when the safety gear is initiated in relation to the minimum breaking load in accordance with the rope manufacturer's specifications.
??????? 對限速器鋼絲繩安全系數應至少為8～1，計算基于繩子的最大應力，當安全性傳動裝置的最小損壞載荷應該和照制造商的規格匹配。
??????? Wiring/pipework used for safety purposes shall be installed and protected to prevent damage due to external influences.
??????? 安全性布線/管道應被安裝設施來保護，以防止由于外部影響損傷。
??????? 13?Response elements used for safety purposes
??????? 1.1.1.3?安全性反應元件
??????? Response elements include, e.g. safety related contactors, full-flow directional valves, locking devices, brakes, safety gear.
??????? 響應要素包括：安全相關的接觸器，全流方向閥，鎖緊裝置，制動器，安全裝置。
??????? 5.2.2.3.1?Full flow directional valves which are used for safety purposes shall be designed so that in the event of valve control pressure failure the valve shall not move to a dangerous position for the system.
??????? 5.2.2.3.1??全流量換向閥，安全性設計應使控制壓力故障的閥門不會移動到一個對系統造成危險的位置。
??????? This requirement may be fulfilled by either:
??????? 此要求可被滿足的條件：
??????? a)?a mechanically and positively actuated full flow directional valve which acts directly on the relevant part of the hydraulic system, or
??????? 機械和正動全流量換向閥，直接作用于液壓系統相關的部分
??????? b)?a pilot operated full flow directional valve controlled by a mechanically and positively actuated hydraulic safety device. The pilot operated full flow directional valve, shall in the event of control pressure failure, positively interrupt the associated movement and prevent further movement in that direction. The full flow directional valve shall also incorporate the following design features to ensure that it shall not be prevented from operating correctly in the event of a spring failure:
??????? 一種先導式全流量換向閥的機械和正動液壓安全控制裝置。先導式全流閥，應控制壓力故障事件，及時中斷相關運動和防止在運動方向上的進一步運動。全流量方向控制閥，還應包括以下的設計特點，以確保它不會在正確的彈簧失效時阻止運行：
??????? i)?compression springs shall be guided to prevent them buckling and prevent the ends becoming displaced during use ; in combination with? ii) or iii)
??????? 壓縮彈簧應遵循預防屈曲和防止端在使用的時候移位；結合II或III
??????? ii)?compression springs shall have both ends guided ; or
??????? 壓縮彈簧的兩端應被引導
??????? iii)?compression springs shall be selected such that the wire diameter is greater than the distance between the coils, hence preventing coils from winding into each other in the event of breakage.
??????? 壓縮彈簧應這樣選擇線徑大于線圈之間的距離，從而防止線圈纏繞到彼此導致破損。
??????? 5.2.2.3.2?Full flow solenoid directional valves shall not be used alone for safety purposes.
??????? 為了保證安全全流量電磁換向閥不能單獨使用。
???????
???????